Simulation Transport Vibrostand (PG-120)
Simulation transport vibrostand is applied to test the anti viberation ability in transit, and it is widely used in the industries of electronics, motor, lighting fixture, package, toy and etc. This equipment can do the low frequency vibration test, vibration resistance test and reliability test to evaluate the products’ quality. Completely meet the requirements of IEC60068-2-6.
● Vibration table: 1100*1200mm
● Vibration mode: back and forth
● Load capacity: 100KG
● Amplitude: 25.4mm
● Oscillation: sine-wave,half-sine-wave
● Power: 1.5KW, 220V±10%, 15A
● Accuracy of frequency: 0.01Hz
● Time: 0~99H99M99S
Relative Environment Test Chamber:
Salt Spray Test Chamber
Salt spray test chamber is applied to measure the reliability of the EUT against salt-spray corrosion. Salt spray chamber is to simulate the climate near the sea, there are two kinds of test according to different standards (JIS, ASTM, CNS, GB), neutral salt mist (NSS) and acidy salt spray test (CASS). This equipment can meet the requirements of the both.
Principle: Absorb the salt water by Bernoulli principle, and the salt water will be atomized by nozzle symmetrically, no block, no crystallize. The heater in the chamber keep the temperature.
Structure and material:
1) The chamber adopts PVC board, the thickness is 5mm, can bear 80℃.
2) The transparent lid is made by Acrylic board, the thickness is 6mm.
3) The saturated air barrel is made by SUS#304 stainless steel.
4) The test rack can be freely to adjust the angle.
1) Power off @ low water
2) Power off @ over heat
3) With alarming indicator
● Temperature requirement:
Lab:35~50℃ (NSS@35℃, CASS@50℃)
Air barrel: 47~63℃ (NSS@47℃, CASS@63℃)
Resolution accuracy: ±0.1℃
Control accuracy: ±0.1℃
Distribution Accuracy: ±2.0℃
|Power (single phase)||220V, 3KW, 50Hz||220V, 1.5KW, 50Hz||220V, 1.5KW, 50Hz|
|Accessories||V rack, nozzle, spray tower, NACL (2 bottles) and etc.|
|L sharp test rack||4 pieces|
|Standard measuring cylinder||1 piece|
|Temperature pointer||2 pieces|
|V Sharp test rack||6 pieces|
|Collector 80cm||1 piece|
|Glass nozzle||1 piece|
|NACL 500g||2 bottle|
|Power cable 2.5m||1 piece|
Relative Environment Test Chamber
IPX5/6 Jet Nozzle/Hose Nozzle
Jet Nozzle is designed according to the requirements of IPX5 and IPX6 code of GB4208 and IEC60529 standard. It’s used to test the waterproof performance of the appliance and electronics.
|Nozzle Hole Diameter||6.3mm||12.5mm|
|Nozzle distance between shell||2.5-3m|
|Test Time||More than 1min/m2 and 3mins|
High-low temperature and humidity chamber
High-low temperature and humidity chamber is a kind of environment test chamber, designed according to IEC60068-2-1, IEC60068-2-2 and IEC60068-2-3. It can accurately simulate the conditions of low temperature, high temperature, low temperature & humidity and high temperature & humidity. It is applied to the industries of electronic, battery, plastic, food, paper, car, LED lamps and so on.
|Temperature range||0~+150℃ -20℃~+150℃ -40℃~+150℃ -60℃~+150℃|
|Humidity range||20%~98% R.H.|
|Accuracy:||Temperature: ±0.01℃; humidity: ±0.1% R.H.|
|Temperature rise speed||2℃-4℃/min|
|Temperature down speed||0.7℃-1℃/min|
|Sensor||Pt 100 resistor|
|Cooling system||Taikang compressor|
|Protection device||Over-heat, over load, leakage, short circuit and etc.|
|Configuration||Φ50 test hole (1 piece), sample shelf (2 pieces), glass view window, floodlight|
|Power supply||380V±10%, 50Hz,3P+N+G|